1.外观图：182.绕组结构绕组开始槽位结束槽位材料规格0.20mm*2P 2UEW背胶铜箔0.05*80.20mm*1P 2UEW0.20mm*1P 2UEW0.20mm*1P 2UEW0.20mm*1P 2UEW0.20mm*1P 2UEW背胶铜箔0.05*80.20mm*1P 2UEW圈数胶带规格/圈数W=14mm T=0.04mm 2TsW=14mm T=0.04mm 2TsW=14mm T=0.04mm 2Ts档墙规格/圈数1-8侧9-16侧W=3mm 0.9Ts/W=3mm 0.9Ts入出线套管L=12mm 26LL=15mm 26LL=12mm 28L绕线要求N1E1N2N3N4N5N6E2N7231091514二三九八十三十二1NC11101615一/十九十四十三70.959910W=3mm 0.9Ts/W=3mm 0.9Ts均绕一层置中绕双线并饶均绕一层双线并饶密绕一层W=14mm T=0.04mm 3Ts20W=2.5mm 0.9TsW=2.5mm 0.9TsW=3mm 0.9Ts/W=3mm 0.9TsW=3mm 0.9Ts/W=3mm 0.9TsL=12mm 28LL=12mm 28LL=15mm 26LL=12mm 28L83七三7NC六/120.9518W=14mm T=0.04mm 2TsW=14mm T=0.04mm 1TsW=14mm T=0.04mm 3Ts均绕一层置中绕均绕一层4四3三*.绕线说明：1.2.3.4.骨架空PIN6,13脚。PIN1脚侧朝机台内，顺时针绕线。绕线前，先在骨架上包一圈胶带再绕线。E1/E2绕组铜箔焊点朝下绕制。铜箔背胶，绕组胶带用高温胶带，厚度0.04mm。产品平贴度0.12mm MAX。*.原理图PRI127843*.铜箔背胶SECN4N5N2N7E1/E2\" \"表示起线端\" \"表示铁氟龙套管N1N616151411109N33.组装：磁芯背胶磁芯组装包磁芯胶带包磁芯胶带(棕色）用高温胶带0.06mm/T*6.5mm/外包三层.点胶磁芯结合处点灰胶固定（4点）.PIN1-8脚侧骨架顶部与磁芯结合处点灰胶固定.喷印/打点产品PIN1-8脚侧居中喷印，字尾朝针脚，PIN1脚打白点标示。（黑色字体）.两磁芯靠引脚侧用0.06mm/T*6.5mm/气隙磁芯装于产品反包一层“E”型胶带，不可有破PIN1-8脚侧.损，以防耐压不良.PIN1PIN8PIN1PIN8组装注意反包胶不能外露，否则会导致PIN与CORE沿面距离不够.如果要剪脚，第6.13脚点“YYWW”为实际生灰胶覆盖（骨架自带空脚产年份周期不需要点胶）4.综合电性测试：NO测试项目测试脚位12客户规格14uH+10%0.5uH MAX─────半品内控规格13.1uH-14.9uH0.4uH MAX(Short Other)85.56mΩ MAX0.44Ω MAX0.79Ω MAX0.35Ω MAX0.55Ω MAX主绕组6.8-7.217.8-18.211.8-12.217.8-18.2成品内控规格12.8uH-15.1uH0.48uH MAX(Short Other)85.56mΩ MAX0.44Ω MAX0.79Ω MAX0.35Ω MAX0.55Ω MAX6.8-7.217.8-18.211.8-12.217.8-18.2测试条件电感漏感2-12-12-19-11100KHz 1V3电阻14-168-74-325℃14-1圈数2-19-118-74-330Ts7Ts18Ts12Ts18Ts20KHZ 1.0V5.耐压测试：NO12345项目耐压耐压耐压耐压耐压脚位/项目2，3，7，9，14-磁芯2，3，7-9，42-3,73-7.39-14.3测试要求/条件AC2700V 2mA 5SAC2700V 2mA 5SAC600V 1mA 3SAC600V 1mA 3SAC600V 1mA 3S
