PT91-21CTR10;中文规格书,Datasheet资料

Technical Data Sheet

1.9mm Round Subminiature“ Z-Bend” Lead Phototransistor

PT91-21C/TR10

Features

․Fast response time ․High photo sensitivity ․Small junction capacitance

․Compatible with infrared and vapor phase reflow solder process. ․Pb free

․The product itself will remain within RoHS compliant versio

Descriptions

․PT91-21C/TR10 is a phototransistor in miniature SMD package which is molded in water clear plastic with spherical top view

lens. The device is spectrally matched to infrared emitting diode.

Applications

․Miniature switch ․Counters and sorter ․Position sensor

․Infrared applied system

Device Selection Guide LED Part No.

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 1 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai

Chip

Material

Lens Color

PT Silicon Water clear http://oneic.com/

PT91-21C/TR10 Collector EmitterPackage Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Rating Units Absolute Maximum Ratings (Ta=25℃)

Parameter SymbolCollector-Emitter Voltage Collector Current Operating Temperature Storage Temperature Soldering Temperature Power Dissipation at(or below)

25℃Free Air Temperature

VCEO 30 V

Emitter-Collector-Voltage VECO 5 V

IC 20 mA

℃ Topr -25 ~ +85 Tstg

-40 ~ +85

℃

Tsol 260 ℃

Pc 75 mW

Notes: *1:Soldering time≦5 seconds.

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 2 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai

http://oneic.com/

PT91-21C/TR10

Electro-Optical Characteristics (Ta=25℃)

Parameter Symbol Condition MinTyp MaxUnit

Rang Of Spectral Bandwidth Wavelength Of Peak Sensitivity Collector-Emitter Breakdown

Voltage

Emitter-Collector Breakdown Voltage

Collector-Emitter Saturation Voltage

Collector Dark Current

10%λP --- 400 --- 1100nm λP BVCEO BVECO VCE(sat) ICEO

--- --- 940 --- nm IC=100μA

Ee=0mW/cm2 IE=100μA Ee=0mW/cm2 IC=2mA Ee=1m W/cm2 VCE=20V Ee=0mW/cm2 VCE=5V Ee=1mW /cm2

30 --- --- V 5 --- --- V --- --- 0.4 V --- --- 100 nA On State Collector Current Rise Time Fall Time

IC(ON) 1.0 1.5 --- mAtr --- 15 --- VCE=5V

IC=1mA μS

tf --- 15 --- RL=1000Ω

Intensity Specifications for Bin Grading

Rank Test Condition Bin1 Bin2 Bin3 Bin4 Bin5

Ee=1mW/cm2 VCE=5V

Min

Max

Unit

1.0 2.0 1.5 3.0 mA 2.0 4.0 2.5 5.0 3.0 6.0

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 3 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai

http://oneic.com/

PT91-21C/TR10 Typical Electro-Optical Characteristics Curves Fig.1Collector Power Dissipation vs. Fig.2 Spectral Sensitivity Ambient Temperature 100806040200 1.0Ta=25C0.80.60.40.20-2502550758510010030050070090011001300Fig.3 Relative Collector Current vs. Fig.4 Collector Current vs. Ambient Temperature Irradiance 10160140120100806040200010202C10.10.010.0010.0130405060700.11210 Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 4 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai http://oneic.com/ PT91-21C/TR10 Typical Electro-Optical Characteristics Curves Fig.5 Collector Dark Current vs. Fig.6 Collector Current vs. Ambient Temperature Collector-Emitter Voltage 10 14121010108210100255075100001234 Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 5 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai

http://oneic.com/

PT91-21C/TR10 Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board.

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 6 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai

http://oneic.com/

PT91-21C/TR10 4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is

unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 7 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai

http://oneic.com/

PT91-21C/TR10

Reliability Test Item And Condition

The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% NO. Item

Test Conditions

Test Hours/Sample Failure Cycles Sizes Judgement

Criteria

Ac/Re

TEMP.：260℃±5℃ 6Mins 22pcs 5secs

2 Temperature Cycle H : 100℃ 15mins50Cycles 22pcs IL≦L×0.8

5mins

L：Lower L : -40℃ 15mins1 REFLOW H :+100℃ 5mins50Cycles 22pcs Specification Limit 10secs

L :-10℃ 5mins

4 High Temperature TEMP.：+100℃ 1000hrs 22pcs Storage 5 Low Temperature TEMP.：-40℃ 1000hrs 22pcs 3 Thermal Shock Storage

6 DC Operating Life =VCE5V 1000hrs 22pcs 7 High Temperature/ 85℃ / 85% R.H 1000hrs 22pcs High Humidity

0/1 0/1

0/1

0/1 0/1 0/1 0/1

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 8 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai

http://oneic.com/

PT91-21C/TR10

Package Dimensions Loaded Quantity Per Reel 1000PCS/Reel Unit :mm

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 9 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai

http://oneic.com/

PT91-21C/TR10 Packing Quantity Specification 1.1000Pcs/1Volume，1Volume/1Bag 2.10Boxes/1Carton Label Form Specification RoHSPT91-21C/TR10 CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification.

2. When using this product, please observe the absolute maximum ratings and the instructions

for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets.

3. These specification sheets include materials protected under copyright of EVERLIGHT

corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.

Tel: 886-2-2267-2000, 2267-9936 EVERLIGHT ELECTRONICS CO., LTD.Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-61, 2267-6306 Taipei 236, Taiwan, R.O.C http:\\\\www.everlight.com Tucheng,

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 2 Page: 10 of 10 Device No：DTT-091-032 Prepared date：08-02-2006 Prepared by：Jaine Tsai

http://oneic.com/

分销商库存信息:

EVERLIGHTPT91-21C/TR10